How To Use Your Smartphone As A Backup Camera

Guide: How to Install a Backup Photographic camera in a RAM Promaster Urban center

Post-obit upwardly on my previous guide on how to install an aftermarket radio supporting carplay, this guide will bear witness you how to install a backup photographic camera into the stock enclosure.

Parts Listing

Fill-in Photographic camera: NATIKA IP69K Waterproof Night Vision 720p Ebay Amazon
Epoxy (I used Loctite repair putty) Ebay Amazon

Tools:

Philips #i and #2 drivers
Wire joining kit: soldering/stripping tools, tap connectors, etc.
Red/black wire for 12V power supply
Some long, flexible, but stiff tool for guiding wires within the body of the van. I used the outer loop of a hoop skirt.

Wiring

The backup camera requires 2 things: 12V power and analog video. The video cable also includes an extra wire which can be used to send the backup signal to the aftermarket radio, merely the Promaster City already includes that indicate in the wiring harness, so we won't exist needing it.

Nosotros'll get 12V ability by tapping into the rear 12V power source, and we'll send analog video on this winding path:

This path follows the factory wiring then the cable volition be hidden. Note that I initially tried going on the driver's side but there's not enough space to pass the cable through in the body (where segment E would be), and so I had to start from scratch on the passenger'southward side.

Okay let's begin!

Segment B

It's way easier to snake the video cablevision from top to lesser, which is why we're doing segment B first. Remove the rubber tube from the torso and door frame, so snake the video cablevision from elevation to bottom. It takes some endeavor, I ended up using the prophylactic hose to push the head down, then grab it, and so pull, and echo, until I could pull it through.

Segment A

Once that's done, you'll want to remove the panel on the within of the commuter's side left door. Use a panel removal tool or slice of plastic to pry the door off.

Once done, you lot'll be able to see where the camera housing is. Side by side, snake your guide wire (I'm took this from a hoop skirt) through these ii points.

Tape the cable's connector to the end of the wire, so pull all the way through:

Exercise the same for the power wire. You'll want to leave about this much hanging from the other end:

Segment B Revisited

Now push your ability cable through the safety tubing, going from bottom to elevation.

In one case consummate, yous should have both ability and video coming through the acme of the rubber tube. Push through the pigsty in the body and receive on the other side to complete.

In that location'southward only one cablevision hither because I did video commencement, and then power. Merely you can do them at the same fourth dimension.

Segment C

Leave the power cablevision hanging from the driver's side hole and ophidian simply the video cable to the passenger side pigsty. Same technique, exit the connector taped to the tail of the guide wire and pull through, like you would with a needle while sewing.

Segment D

There's a console you'll need to remove to go access for this department but the pins pull right out when you pull with your console removal tool.

Segment E

Remove the console where you lot footstep into the van on the passenger's side. It'south held in place with mainly screws and velcro. You'll need the Philips #ane caput for these screws.

Pass the cable through, following the existing wire, but don't become past the door withal.

Segment F

You'll desire to remove the aforementioned step panel in the rider cabin.

Earlier you tin remove it, you'll need to undo a single spiral where the passenger's feet go. Then, pop the panel off.

Now that both sections are attainable, ophidian the wire all the manner through.

Segment G

The carpet underneath the glove box is held in place with two pins, pull to release, then run the cable along the bottom.

Segment H

Snake the cable through to the inside of the dash.

At this point you can tie the cable to the car'south wiring harness with either tesa record or a zip tie.

Borer Power

Remove the 12V vehicle power from the driver's side rear by pushing in and pushing upward:

The power supply cable that comes with this photographic camera isn't long enough. Cutting effectually 5 ft of your own wire, bind together with tesa tape or zip ties, and snake through to the top hole so you can run into the existing power supply cable.

Strip both wires and join them. I used solder.

Then null tie the package and stash abroad in that pigsty.

On the other end, y'all'll need to tap into the power supply. I stripped the wire and soldered my new wire inline:

I messed up my first effort, be certain to get out ample exposed wire for soldering!

Testing

It's always skillful to test early so if anything went wrong you tin can fix it without having to disassemble things once more.

Connect the camera to power and video, connect video to your radio, effort putting your car in reverse and seeing if information technology works. If it doesn't work, test the leads for ability and video. Note that in the pioneer radio you have to go into the settings to enable the backup photographic camera or AV input.

Mounting the Camera

I spent a lot of time considering my options for bracketing the photographic camera on. Subsequently all, it you lot tin see in the picture show that there are two holes for screws. However, I found information technology then incredibly unwieldy to piece of work in the small infinite that I abandoned this plan (after losing a few screws to the void below). Instead I used epoxy, which hardens to produce a waterproof seal and binds the materials together.

It looks roomy in this picture simply there's barely enough space to fit my fingers, let alone a screwdriver.

You'll want to cutting out a big enough foursquare hole to sit the entire front part of the photographic camera in. Cut a circular hole and sitting the photographic camera behind it won't work with this photographic camera I've called, as information technology'south such a wide bending that the plastic obstructs part of its view.

Start with the smallest hole and line it up with the center.

I followed upwardly with the largest drill scrap I had, and then used my dremel to cut away at material until the camera fit snugly.

Next cut out a slice of epoxy, follow directions to mix thoroughly. If you haven't used epoxy earlier (like me), try it out on another materials before you lot do the final adhesion, to get the hang of information technology.

Steps you'll want to keep in mind are:

Make certain you lot can prepare the epoxy 24 hours, equally close to room temperature as possible (below 60 degrees and it starts existence problematic).
Embrace the camera lens with painter's tape so you don't get it dirty.
Clean all surfaces thoroughly.
Use a file or sandpaper to add some texture to the camera body.

I don't know how it'll concur upwards, simply it seems to piece of work correct now. In the time to come I'll find a way to paint the epoxy so it matches the color of the license frame too.

Finalizing the Wiring

Afterward testing everything works one last fourth dimension, use cypher ties or tesa tape to tie the cables where appropriate. For case you probably want to tie the video cable to the manufacturing plant cable lines to keep things neat. When you lot're washed, yous can re-install your radio and re-attach the panels from earlier.

And that's it. Allow me know in the comments beneath if you have any questions (if annihilation is unclear, etc). Thanks for reading.

Source: https://medium.com/@chris_41792/guide-how-to-install-a-backup-camera-in-a-ram-promaster-city-db479dd2fe78

Posted by: gerstnercappraid.blogspot.com